View SAA7219_1092544.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

d a t a sh eet product speci?cation supersedes data of 1999 sep 20 file under integrated circuits, ic02 2000 jun 14 integrated circuits SAA7219 mpeg2 transport risc processor
2000 jun 14 2 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 contents 1 features 1.1 external interfaces 1.2 cpu related features 1.3 mpeg2 systems features 2.1 SAA7219 overview 2.2 SAA7219 in a dvb system 3 ordering information 5 pinning 6 application information 6.1 memory configurations 7 package outline 8.1 introduction to soldering surface mount packages 8.2 reflow soldering 8.3 wave soldering 8.4 manual soldering 8.5 suitability of surface mount ic packages for wave and reflow soldering methods 9 data sheet status 10 definitions 11 disclaimers
2000 jun 14 3 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 1 features conditional access descrambling digital video broadcasting (dvb) compliant and multi2 compliant stream demultiplexing: transport stream (ts), packetized elementary stream (pes), program and proprietary streams internal 32-bit mips risc based central processing unit (cpu) supporting mips16 instruction set and running at 81 mhz low-power sleep modes supported across the chip comprehensive driver software and development tool support package: sqfp208. 1.1 external interfaces versatile compressed stream input at 108 mbits/s a 32-bit microcontroller extension bus supporting dram, sdram, flash, (e)prom and external memory mapped i/o devices. it also supports a synchronous interface to communicate with the integrated mpeg audio video graphics decoder (avgd) saa7215 at 40.5 mbytes. an ieee 1284 interface (centronics) supporting master and slave modes. usable as a general purpose port. an interface to ieee 1394 devices (such as philips pdi 1394 chip-set) two uart (rs232) data ports with direct memory access (dma) capabilities (187.5 kbits/s) including hardware flow control signals rxd, txd, rts and cts for modem support a synchronous serial interface (ssi) to connect an off-chip modem analog front-end an elementary uart with dma capabilities, dedicated to front panel devices for instance two dedicated smart-card reader interfaces (iso 7816 compatible) with dma capabilities two i 2 c-bus master/slave transceivers with dma capabilities, supporting the standard (100 kbit/s) and fast (400 kbits/s) i 2 c-bus modes 32 general purpose, bidirectional i/o interface pins, 8 of which may also be used as interrupt inputs one pulse width modulated (pwm) output with 8-bit resolution a general purpose/high-speed (gp/hs) interface supporting stream recording through ieee 1394 interface ic an extended jtag interface for board test support. 1.2 cpu related features the SAA7219 contains an embedded risc cpu, which incorporates the following features: a 32-bit pr3930 core running at 81 mhz 8-kbyte, 2-way set associative instruction cache 4-kbyte, 4-way set associative data cache a programmable low-power mode, including wake-up on interrupt a memory management unit with 32 odd/even entries and variable page sizes multiply/accumulate/divide unit with fast multiply/accumulate for 16-bit and 32-bit operands two fully independent 24-bit timers and one 24-bit timer including watchdog facilities a real-time clock unit (active in sleep mode) built-in software debug support unit as part of extended enhanced jtag debug interface on-chip sram of 4 kbytes for storing code which needs fast execution. 1.3 mpeg2 systems features hardware based parsing of transport stream (ts), philips semiconductors program and proprietary software data streams. maximum input rate is 108 mbits/s. a real-time descrambler consisting of 3 modules: C a control word bank containing 14 pairs (odd, even) of control words and a default control word C the dvb descrambler core implementing the stream decipher and block decipher algorithms C the multi2 descrambler algorithm implementing the cbc and ofb mode descrambling functions.
2000 jun 14 4 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 hardware section filtering based on 32 different packet identifiers (pids) with a flexible number of filter conditions (8 or 4-byte condition plus 8 or 4-byte mask) per pid and a total filter capacity of 40 (8-byte condition checks) or up to 80 (4-byte condition checks) filter conditions: C 4 ts/pes filters for retrieval for data at ts or pes level for applications such as subtitling, txt or retrieval of private data C flexible dma based storage of the 32 section substreams and 4 ts/pes data substreams in the external memory. system time base management with a double counter mechanism for clock control and discontinuity handling, 2 presentation time stamp (pts)/decoding time stamp (dts) timers a gp/hs filter which can serve as an alternate input from for example ieee 1394 devices. the ieee 1394 gp/hs mode supports packet insertion and has an internal sram for storing 2 packets. it can also output either scrambled or descrambled ts to ieee 1394 devices. 2 general description 2.1 SAA7219 overview the device is part of a comprehensive source decoding kit which contains all the hardware and software required to receive and decode mpeg2 transport streams, including descrambling, demultiplexing. in addition, it includes a pr3930 core which is a 32-bit mips risc-based cpu core supporting the mips 16 instruction set to reduce memory requirements and several peripheral interfaces such as uarts, i 2 c-bus units, an iec 1883, and an ieee 1284 (centronics) interface. the SAA7219 is therefore capable of performing all controller tasks in digital television receiver applications such as set-top boxes. furthermore, the SAA7219 is compliant to dvb and multi2 standards. the SAA7219 receives transport streams through a versatile stream input interface capable of handling both byte-parallel and bit-serial streams in various formats, supporting data streams up to and including 13.5 mbyte/s (108 mbits/s). the stream data is first applied to an on-chip descrambler incorporating a dvb descrambling algorithm, on the basis of 14 control word pairs stored in on-chip ram. demultiplexing is subsequently applied to the stream, to separate up to 32 individual data streams. the demultiplexer section includes clock recovery and timebase management. program specific information (psi), service information (si), conditional access (ca) messages and private data are selected and stored in external memory, for subsequent off-line processing by the internal pr3930 cpu core. to support advanced board testing facilities the SAA7219 includes boundary scan test hardware, according to the ejtag standard. the device features a low-power sleep mode, which is capable of sustaining set-top box standby functionality, thus eliminating the need for a separate front panel controller. the SAA7219 requires a supply voltage of 3.3 v and most devices input and output interfaces are 5 v tolerant except the extension bus which is 3.3 v only. the SAA7219 is mounted in a sqfp208 package. 2.2 SAA7219 in a dvb system the SAA7219 has been designed to offer optimum performance when used with the saa7215 for mpeg2 avg decoding. synchronous bus interface transfer at 40.5 mhz on 16 bits saa7215 has one dedicated sdram for mpeg2 audio video handling and one for graphics and cpu data. the second memory offers high bandwidth and low latency to the SAA7219 when accessing it to download graphics or executing some applications. this enables a high level of performance together with a low system cost by having one sdram for graphics and cpu data. 3 ordering information type number package name description version SAA7219hs/c2 sqfp208 plastic shrink quad ?at package; 208 leads (lead length 1.3 mm); body 28 28 3.4 mm; high stand-off height sot316-1
2000 jun 14 5 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 this text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader .this text is here in _ white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader.this text is here inthis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader. white to force landscape pages to be ... 4 block diagram l pagewidth fce374 pi-bus ctrl input interface gp/hs interface 1394 gateway mips pr3930 core data cache instruction cache timer 1 timer 2 dsu ejtag timer 3 (watchdog) av filter audio and video interface avd interface mpeg system int.handler mpeg system gateway pcr processing filter dma controller ts/pes filters mmu section filters pid filter descrambler dvb and multi2 mpeg system-bus reset clock jtag peripheral section extension bus controller card reader uart 01 01 0 ss mm pi-bus s s m m m cpu section output stream input stream pwm demultiplexer descrambler section ss s 1 2 pio interface i 2 c 1284 1284 bus 32-bit pio external bus interface jtag interface uart and ssi connections scl and sda lines ssi rtc 32 khz interrupt controller 4-kbyte sram smart card interface fig.1 block diagram. m = master peripheral with embedded dma channel s = slave peripheral
2000 jun 14 6 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 this text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader .this text is here in _ white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader.this text is here inthis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader. white to force landscape pages to be ... 5 pinning table 1 sqfp208 package: 179 functional pins and 29 power supply pins symbol pin i/o buffer type volt (1) description pio interface (32 pins) pio0 to pio7 105 to 112 i/o bidirectional, 3 ma output drive 5 v usable as interrupt inputs and/or i/o lines pio8/bootis32 113 i/o bidirectional, 3 ma output drive 5 v pio bit and pio-strap. at power-on, it indicates the data bus size of the booting device. pio9/bootis16 114 i/o bidirectional, 3 ma output drive 5 v pio bit and pio-strap. at power-on, if bootis32 is low, it indicates if the system should reboot from a 16-bit or 8-bit device. pio10 to pio15 116 to 121 i/o bidirectional, 3 ma output drive 5 v pio bit and pio-strap pio(31:16)/d(31:16) 2, 4 to 9, 11 to 16, 18 to 20 i/o bidirectional, 6 ma output drive 5 v i/o lines or upper 16-bit data bus. the data bus width of the booting device is automatically con?gured at power-on. extension bus (58 pins) d15 to d0 21, 22, 24, 25, 28 to 30, 33 to 36, 38 to 41 i/o bidirectional, 8 ma output drive 3.3 v lower 16-bit data bus a0 to a21 63 to 65, 67 to 71, 73 to 77, 81 to 85, 87 to 90 o 8 ma output drive 3.3 v address bus ras0n 49 o 8 ma output drive 3.3 v row access strobe for dram and sdram bank 0 ras1n/dcs1n 48 o 8 ma output drive 3.3 v row access strobe for dram and sdram bank 1 lcasn 46 o 8 ma output drive 3.3 v column access strobe lower byte mlcasn 43 o 8 ma output drive 3.3 v column access strobe mid lower byte mucasn 44 o 8 ma output drive 3.3 v column access strobe mid upper byte ucasn 42 o 8 ma output drive 3.3 v column access strobe upper byte wen 62 o 8 ma output drive 3.3 v write enable dcs0n 47 o 8 ma output drive 3.3 v chip select for sdram bank 0 cs6n to cs0n 50 to 56 o 8 ma output drive 3.3 v chip select oen 58 o 8 ma output drive 3.3 v output enable dtackn 59 i ttl input 5 v data termination acknowledge. asserted low by the peripheral when the data bus is valid. cs_sdn 60 o 2 ma output drive 3.3 v selects the graphics sdram memory space of the saa7215
2000 jun 14 7 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 this text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader .this text is here in _ white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader.this text is here inthis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader. white to force landscape pages to be ... cs_rgn 61 o 2 ma output drive 3.3 v selects the control registers of the saa7215 clk 91 o 8 ma output drive 3.3 v 40.5 mhz clock uart 0 interface (4 pins) rxd0 141 i ttl input 5 v uart 0 receive data line or receive serial data txd0 142 o 2 ma output drive 3.3 v uart 0 transmit data line or transmit serial data rtsn0 143 o 2 ma output drive 3.3 v uart 0 request to send ctsn0 144 i ttl input 5 v uart 0 clear to send uart 1 and ssi interfaces (5 pins) rxd1/v34_rxd 137 i ttl input 5 v uart 1 receive data line or receive serial data of the ssi interface txd1/v34_txd 138 o 2 ma output drive 3.3 v uart 1 transmit data line or transmit serial data of the ssi interface rtsn1/v34_fs 139 i/o bidirectional, 3 ma output drive 5 v uart 1 request to send (output) or frame synchronization reference of the ssi interface (input) ctsn1/v34_clk 140 i ttl input 5 v uart 1 clear to send or serial input interface clock of the ssi interface (up to 3.375 mhz) mclk 146 o 2 ma output drive 3.3 v master clock for the ssi interface (36.684 mhz) uart 2 interface (2 pins) rxd2 135 i ttl input 5 v uart 2 receive data line txd2 136 o 2 ma output drive 3.3 v uart 2 transmit data line i 2 c-bus 0 interface (2 pins) scl0 149 i/o bidirectional with open-drain 8 ma output drive 5v i 2 c-bus 0 clock line sda0 150 i/o bidirectional with open-drain 8 ma output drive 5v i 2 c-bus 0 data line symbol pin i/o buffer type volt (1) description
2000 jun 14 8 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 this text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader .this text is here in _ white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader.this text is here inthis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader. white to force landscape pages to be ... i 2 c-bus 1 interface (2 pins) scl1 147 i/o bidirectional with open-drain 8 ma output drive 5v i 2 c-bus 1 clock line sda1 148 i/o bidirectional with open-drain 8 ma output drive 5v i 2 c-bus 1 data line smart card 0 interface (5 pins) clk_card0 128 o 2 ma output drive 3.3 v iso uart 0 card clock cmdvccn0 129 o 2 ma output drive 3.3 v iso uart 0 command of the vcc rstin0 132 o 2 ma output drive 3.3 v iso uart 0 reset of the card offn0 133 i ttl input 5 v iso uart 0 card presence sc_i/o0 134 i/o bidirectional with open-drain 8 ma output drive 5 v iso uart 0 i/o line smart card 1 interface (5 pins) clk_card1 122 o 2 ma output drive 3.3 v iso uart 1 card clock cmdvccn1 123 o 2 ma output drive 3.3 v iso uart 1 command of the vcc rstin1 124 o 2 ma output drive 3.3 v iso uart 1 reset of the card offn1 125 i ttl input 5 v iso uart 1 card presence sc_i/o1 126 i/o bidirectional with open-drain 8 ma output drive 5 v iso uart 1 i/o line input stream interface (11 pins) pktstrobe 154 i ttl input 5 v byte strobe or bit strobe pktsync 155 i ttl input 5 v packet synchronization pktvalid 156 i ttl input 5 v data valid, or bit stream word select pktdata7 to pktdata0 157 to 164 i ttl input 5 v 8-bit primary ts data input gp/hs interface (11 pins) gpdata7 to gpdata0 166 to 169, 171 to 174 i/o bidirectional, 3 ma output drive 5 v gp/hs data bus gpvalid 175 i/o bidirectional, 3 ma output drive 5 v gp/hs control lines gpsync 176 i/o bidirectional, 3 ma output drive 5 v gp/hs control lines gpstrobe 177 i/o bidirectional, 3 ma output drive 5 v gp/hs control lines symbol pin i/o buffer type volt (1) description
2000 jun 14 9 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 this text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader .this text is here in _ white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader.this text is here inthis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader. white to force landscape pages to be ... saa7215 mpeg interface (11 pins) v_strobe 93 o 2 ma output drive 3.3 v high-to-low transition strobes the video data in the av_data stream a_strobe 94 o 2 ma output drive 3.3 v high-to-low transition strobes the audio data in the av_data stream av_error 95 o 2 ma output drive 3.3 v ?ag for bit stream error (active high) av_data7 to av_data0 96 to 103 o 2 ma output drive 3.3 v mpeg audio/video stream output port ieee 1284 interface (18 pins) gpd0 to gpd7 190 to 197 i/o bidirectional, 3 ma output drive 5 v parallel data bus nselectin 199 i/o bidirectional, 3 ma output drive 5 v host to peripheral select line ninit 200 i/o bidirectional, 3 ma output drive 5 v host to peripheral control line nstrobe 201 i/o bidirectional, 3 ma output drive 5 v host to peripheral strobe line nack 202 i/o bidirectional, 3 ma output drive 5 v peripheral acknowledge line busy 203 i/o bidirectional, 3 ma output drive 5 v peripheral busy line perror 204 i/o bidirectional, 3 ma output drive 5 v peripheral error line select 205 i/o bidirectional, 3 ma output drive 5 v peripheral on-line nautof 206 i/o bidirectional, 3 ma output drive 5 v host to peripheral control line nfault 207 i/o bidirectional, 3 ma output drive 5 v peripheral error line dir1284 208 o 2 ma output drive 3.3 v direction control of the external buffers pwm interface (1 pin) pwm0 165 o open-drain 8 ma output drive 5 v open-drain 5 v tolerant for vcxo control system interface (3 pins) resetn 1 i/o bidirectional with open-drain 8 ma output drive and schmitt trigger input with high hysteresis 3.3 v general system reset; active low. the pad is bidirectional with an open-drain which is asserted low when the internal watchdog time out is detected. xtal1 153 i 3.3 v 13.5 mhz crystal input xtal2 152 o 3.3 v 13.5 mhz crystal output symbol pin i/o buffer type volt (1) description
2000 jun 14 10 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 this text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader .this text is here in _ white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader.this text is here inthis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader. white to force landscape pages to be ... jtag and test interface (5 pins) tdo 178 o 3-state, 2 ma output drive 3.3 v test data output/target pc output. real-time trace mode off. serial output data is shifted from jtag instruction register to the tdo pin on the falling edge of the tck clock. when no data is shifted out, tdo is 3-stated. real-time trace mode on. tdo provides non-sequential program counter output at the processor clock speed. tdi 179 i ttl input 5 v test data input/debug interrupt. real-time trace mode off. serial input data (tdi) is shifted into the jtag instruction register or data register on the rising edge of the tck clock, depending of the tap controller state. real-time trace mode on. an active low level at this input sampled by tck positive edge, is used as interrupt to switch the real-time trace mode off (standard jtag). tms 180 i ttl input 5 v test mode select. this input is decoded by the tap controller to control test operation. sampled on the rising edge of tck. trst 181 i ttl input 5 v test reset. active low level for asynchronous reset of the ejtag module, independent of the processor logic. tck 184 i ttl input 5 v test clock. input clock used to shift data into or out from the jtag instruction or data register. ejtag extension reserved for pr3930 (4 pins) dsu_clk 185 o 2 ma output drive 3.3 v dsu clock is equivalent to the processor clock. captures address and data from pin tdo when pc trace mode is on. is 3-stated when bit 0 or 15 of the jtag control register is logic 0. pcst0 to pcst2 186, 188 and 189 o 2 ma output drive 3.3 v cpu status: debug mode, pipeline stall, occurrence of exception symbol pin i/o buffer type volt (1) description
2000 jun 14 11 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 this text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader .this text is here in _ white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader.this text is here inthis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the acrobat reader. white to force landscape pages to be ... note 1. 5 v tolerant inputs can receive signals swinging between v ss and 3.3 v or v ss and 5 v. 5 v tolerant bidirectional i/o pins can receive signals swinging between v ss and 3.3 v or v ss and 5 v when they are inputs and swing between v ss and v dd when they are outputs. supplies (29 pins) v dd(p) 3, 17, 31, 43, 66, 80, 92, 115, 145 and 187 -- - pad supply voltage v ss(p) 10, 23, 37, 57, 72, 86, 104, 127, 170 and 198 -- - ground supply v dd(c) 27, 79, 130 and 182 -- - core supply voltage v ss(c) 26, 78, 131 and 183 -- - ground supply v dd(pll) 151 -- - analog supply for the on-chip plls symbol pin i/o buffer type volt (1) description fig.2 pin configuration handbook, halfpage SAA7219 1 208 157 53 104 52 156 105 fce380
2000 jun 14 12 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 6 application information handbook, full pagewidth fce375 a dac tda8004 smart cards telecommunication i/f flash dram (optional) vxx modem ieee 1394 l + phy buffers ieee 1384 rs232 ieee 1394 16-mbit sdram 16-mbit sdram (optional) front panel control saa8044 (sdd) tda8060 tda5056 tuner switching scart1 scart2 scart3 saa7215 SAA7219 av pes mpeg ts i 2 c-bus rf in 2 lr cvbs/yc rgb fig.3 set-top box example.
2000 jun 14 13 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 6.1 memory con?gurations table 2 low-end and high-end memory con?gurations configuration sdram dram prom flash peripherals low-end 1m 16 256k 16 512k 8 - high-end up to 2 banks of 64 mbits up to 2 banks of 4 mbytes up to 4 mbytes 2 to 7 banks of up to 4 mbytes fig.4 typical low-end memory configuration. fce376 SAA7219 saa7215 dram/ sdram sdram (mpeg) prom 16 8 16 16 flash reserved fig.5 typical high-end unified memory configuration. fce377 SAA7219 saa7215 dram sdram (mpeg) sdram graphics prom 32 16 16 16 flash 1 flash 2
2000 jun 14 14 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 7 package outline unit a 1 a 2 a 3 b p ce (1) eh e ll p z y w v q references outline version european projection issue date iec jedec eiaj mm 0.50 0.25 3.6 3.2 0.25 0.27 0.17 0.20 0.09 28.1 27.9 0.5 30.9 30.3 1.39 1.11 8 0 o o 0.08 0.2 1.3 0.08 dimensions (mm are the original dimensions) note 1. plastic or metal protrusions of 0.25 mm maximum per side are not included. 0.75 0.45 sot316-1 ms-029 99-12-27 00-01-25 d (1) (1) (1) 28.1 27.9 h d 30.9 30.3 e z 1.39 1.11 d pin 1 index b p e q e a 1 a l p detail x l (a ) 3 b 52 c d h b p e h a 2 v m b d z d a z e e v m a x 1 208 157 156 105 104 53 y w m w m 0 5 10 mm scale 208 leads (lead length 1.3 mm); body 28 x 28 x 3.4 mm; high stand-off height sqfp208: plastic shrink quad flat package; sot316-1 a max. 4.10
2000 jun 14 15 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 8 soldering 8.1 introduction to soldering surface mount packages this text gives a very brief insight to a complex technology. a more in-depth account of soldering ics can be found in our data handbook ic26; integrated circuit packages (document order number 9398 652 90011). there is no soldering method that is ideal for all surface mount ic packages. wave soldering is not always suitable for surface mount ics, or for printed-circuit boards with high population densities. in these situations reflow soldering is often used. 8.2 re?ow soldering reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. several methods exist for reflowing; for example, infrared/convection heating in a conveyor type oven. throughput times (preheating, soldering and cooling) vary between 100 and 200 seconds depending on heating method. typical reflow peak temperatures range from 215 to 250 c. the top-surface temperature of the packages should preferable be kept below 230 c. 8.3 wave soldering conventional single wave soldering is not recommended for surface mount devices (smds) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. to overcome these problems the double-wave soldering method was specifically developed. if wave soldering is used the following conditions must be observed for optimal results: use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave. for packages with leads on two sides and a pitch (e): C larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; C smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. the footprint must incorporate solder thieves at the downstream end. for packages with leads on four sides, the footprint must be placed at a 45 angle to the transport direction of the printed-circuit board. the footprint must incorporate solder thieves downstream and at the side corners. during placement and before soldering, the package must be fixed with a droplet of adhesive. the adhesive can be applied by screen printing, pin transfer or syringe dispensing. the package can be soldered after the adhesive is cured. typical dwell time is 4 seconds at 250 c. a mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. 8.4 manual soldering fix the component by first soldering two diagonally-opposite end leads. use a low voltage (24 v or less) soldering iron applied to the flat part of the lead. contact time must be limited to 10 seconds at up to 300 c. when using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 c.
2000 jun 14 16 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 8.5 suitability of surface mount ic packages for wave and re?ow soldering methods notes 1. all surface mount (smd) packages are moisture sensitive. depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). for details, refer to the drypack information in the data handbook ic26; integrated circuit packages; section: packing methods . 2. these packages are not suitable for wave soldering as a solder joint between the printed-circuit board and heatsink (at bottom version) can not be achieved, and as solder may stick to the heatsink (on top version). 3. if wave soldering is considered, then the package must be placed at a 45 angle to the solder wave direction. the package footprint must incorporate solder thieves downstream and at the side corners. 4. wave soldering is only suitable for lqfp, tqfp and qfp packages with a pitch (e) equal to or larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. 5. wave soldering is only suitable for ssop and tssop packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. package soldering method wave reflow (1) bga, lfbga, sqfp, tfbga not suitable suitable hlqfp, hsqfp, hsop, htqfp, htssop, sms not suitable (2) suitable plcc (3) , so, soj suitable suitable lqfp, qfp, tqfp not recommended (3)(4) suitable ssop, tssop, vso not recommended (5) suitable
2000 jun 14 17 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 9 data sheet status note 1. please consult the most recently issued data sheet before initiating or completing a design. data sheet status product status definitions (1) objective speci?cation development this data sheet contains the design target or goal speci?cations for product development. speci?cation may change in any manner without notice. preliminary speci?cation quali?cation this data sheet contains preliminary data, and supplementary data will be published at a later date. philips semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. product speci?cation production this data sheet contains ?nal speci?cations. philips semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. 10 definitions short-form specification ? the data in a short-form specification is extracted from a full data sheet with the same type number and title. for detailed information see the relevant data sheet or data handbook. limiting values definition ? limiting values given are in accordance with the absolute maximum rating system (iec 60134). stress above one or more of the limiting values may cause permanent damage to the device. these are stress ratings only and operation of the device at these or at any other conditions above those given in the characteristics sections of the specification is not implied. exposure to limiting values for extended periods may affect device reliability. application information ? applications that are described herein for any of these products are for illustrative purposes only. philips semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 11 disclaimers life support applications ? these products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. philips semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify philips semiconductors for any damages resulting from such application. right to make changes ? philips semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. philips semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. 12 purchase of philips i 2 c components purchase of philips i 2 c components conveys a license under the philips i 2 c patent to use the components in the i 2 c system provided the system conforms to the i 2 c specification defined by philips. this specification can be ordered using the code 9398 393 40011.
2000 jun 14 18 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 notes
2000 jun 14 19 philips semiconductors product speci?cation mpeg2 transport risc processor SAA7219 notes
? philips electronics n.v. sca all rights are reserved. reproduction in whole or in part is prohibited without the prior written consent of the copyright owne r. the information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. no liability will be accepted by the publisher for any consequence of its use. publication thereof does not con vey nor imply any license under patent- or other industrial or intellectual property rights. internet: http://www.semiconductors.philips.com 2000 70 philips semiconductors C a worldwide company for all other countries apply to: philips semiconductors, marketing communications, building be-p, p.o. box 218, 5600 md eindhoven, the netherlands, fax. +31 40 27 24825 argentina: see south america australia: 3 figtree drive, homebush, nsw 2140, tel. +61 2 9704 8141, fax. +61 2 9704 8139 austria: computerstr. 6, a-1101 wien, p.o. box 213, tel. +43 1 60 101 1248, fax. +43 1 60 101 1210 belarus: hotel minsk business center, bld. 3, r. 1211, volodarski str. 6, 220050 minsk, tel. +375 172 20 0733, fax. +375 172 20 0773 belgium: see the netherlands brazil: see south america bulgaria: philips bulgaria ltd., energoproject, 15th floor, 51 james bourchier blvd., 1407 sofia, tel. +359 2 68 9211, fax. +359 2 68 9102 canada: philips semiconductors/components, tel. +1 800 234 7381, fax. +1 800 943 0087 china/hong kong: 501 hong kong industrial technology centre, 72 tat chee avenue, kowloon tong, hong kong, tel. +852 2319 7888, fax. +852 2319 7700 colombia: see south america czech republic: see austria denmark: sydhavnsgade 23, 1780 copenhagen v, tel. +45 33 29 3333, fax. +45 33 29 3905 finland: sinikalliontie 3, fin-02630 espoo, tel. +358 9 615 800, fax. +358 9 6158 0920 france: 51 rue carnot, bp317, 92156 suresnes cedex, tel. +33 1 4099 6161, fax. +33 1 4099 6427 germany: hammerbrookstra?e 69, d-20097 hamburg, tel. +49 40 2353 60, fax. +49 40 2353 6300 hungary: see austria india: philips india ltd, band box building, 2nd floor, 254-d, dr. annie besant road, worli, mumbai 400 025, tel. +91 22 493 8541, fax. +91 22 493 0966 indonesia: pt philips development corporation, semiconductors division, gedung philips, jl. buncit raya kav.99-100, jakarta 12510, tel. +62 21 794 0040 ext. 2501, fax. +62 21 794 0080 ireland: newstead, clonskeagh, dublin 14, tel. +353 1 7640 000, fax. +353 1 7640 200 israel: rapac electronics, 7 kehilat saloniki st, po box 18053, tel aviv 61180, tel. +972 3 645 0444, fax. +972 3 649 1007 italy: philips semiconductors, via casati, 23 - 20052 monza (mi), tel. +39 039 203 6838, fax +39 039 203 6800 japan: philips bldg 13-37, kohnan 2-chome, minato-ku, tokyo 108-8507, tel. +81 3 3740 5130, fax. +81 3 3740 5057 korea: philips house, 260-199 itaewon-dong, yongsan-ku, seoul, tel. +82 2 709 1412, fax. +82 2 709 1415 malaysia: no. 76 jalan universiti, 46200 petaling jaya, selangor, tel. +60 3 750 5214, fax. +60 3 757 4880 mexico: 5900 gateway east, suite 200, el paso, texas 79905, tel. +9-5 800 234 7381, fax +9-5 800 943 0087 middle east: see italy netherlands: postbus 90050, 5600 pb eindhoven, bldg. vb, tel. +31 40 27 82785, fax. +31 40 27 88399 new zealand: 2 wagener place, c.p.o. box 1041, auckland, tel. +64 9 849 4160, fax. +64 9 849 7811 norway: box 1, manglerud 0612, oslo, tel. +47 22 74 8000, fax. +47 22 74 8341 pakistan: see singapore philippines: philips semiconductors philippines inc., 106 valero st. salcedo village, p.o. box 2108 mcc, makati, metro manila, tel. +63 2 816 6380, fax. +63 2 817 3474 poland : al.jerozolimskie 195 b, 02-222 warsaw, tel. +48 22 5710 000, fax. +48 22 5710 001 portugal: see spain romania: see italy russia: philips russia, ul. usatcheva 35a, 119048 moscow, tel. +7 095 755 6918, fax. +7 095 755 6919 singapore: lorong 1, toa payoh, singapore 319762, tel. +65 350 2538, fax. +65 251 6500 slovakia: see austria slovenia: see italy south africa: s.a. philips pty ltd., 195-215 main road martindale, 2092 johannesburg, p.o. box 58088 newville 2114, tel. +27 11 471 5401, fax. +27 11 471 5398 south america: al. vicente pinzon, 173, 6th floor, 04547-130 s?o paulo, sp, brazil, tel. +55 11 821 2333, fax. +55 11 821 2382 spain: balmes 22, 08007 barcelona, tel. +34 93 301 6312, fax. +34 93 301 4107 sweden: kottbygatan 7, akalla, s-16485 stockholm, tel. +46 8 5985 2000, fax. +46 8 5985 2745 switzerland: allmendstrasse 140, ch-8027 zrich, tel. +41 1 488 2741 fax. +41 1 488 3263 taiwan: philips semiconductors, 5f, no. 96, chien kuo n. rd., sec. 1, taipei, taiwan tel. +886 2 2134 2451, fax. +886 2 2134 2874 thailand: philips electronics (thailand) ltd., 60/14 moo 11, bangna trad road km. 3, bagna, bangkok 10260, tel. +66 2 361 7910, fax. +66 2 398 3447 turkey: yukari dudullu, org. san. blg., 2.cad. nr. 28 81260 umraniye, istanbul, tel. +90 216 522 1500, fax. +90 216 522 1813 ukraine : philips ukraine, 4 patrice lumumba str., building b, floor 7, 252042 kiev, tel. +380 44 264 2776, fax. +380 44 268 0461 united kingdom: philips semiconductors ltd., 276 bath road, hayes, middlesex ub3 5bx, tel. +44 208 730 5000, fax. +44 208 754 8421 united states: 811 east arques avenue, sunnyvale, ca 94088-3409, tel. +1 800 234 7381, fax. +1 800 943 0087 uruguay: see south america vietnam: see singapore yugoslavia: philips, trg n. pasica 5/v, 11000 beograd, tel. +381 11 3341 299, fax.+381 11 3342 553 printed in the netherlands 753504/02/pp 20 date of release: 2000 jun 14 document order number: 9397 750 06809

▲Up To Search▲

Price & Availability of SAA7219

	To Download SAA7219 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .